The J-Link also has the option of further software enhancements with the production flash programming utility (J-Flash). The ability to take full advantage of the development environment using the Unlimited Flash Breakpoint module also means you free your development from the hardware breakpoint restriction. In this test, J-Link is the clear winner.
We do not recommend or support the following programming methods via J-Link Commander or J-Flash Lite for production purposes. Regarding production programming, only production grade programming tools should be used.
usb production tool v1 34 14
Production grade programming tools typically feature a more sophisticated, multi-step verification process. Many applications also require customization / patching of variable data such as serial number(s), MAC addresses and similar.
Flasher is a programming tool for all common devices with internal or external flash memory. For a list of all supported devices click here. Flasher ARM is designed for programming flash targets with the J-Flash software or stand-alone. Flasher can also operate as a normal J-Link.
A "thermals" design flaw has been noted in the RAMPS 1.4 Eagle CAD files. This has been confirmed by visual inspection of production boards, which consistently shows only between two and three (almost never four) thermal-isolating traces per side of the PCB, to power-carrying pins, of under a 0.5 amp carrying-capacity per trace, assuming a 1oz copper thickness.
Carbon fiber-framed indoor LED video wall and floor displays with exceptional on-camera visual properties and deployment versatility for various installations including virtual production and extended reality.
#include "wio_tracker.h"char message[128] = "Hello from Wio Traker!";WioTracker wio = WioTracker();void setup() wio.Power_On(); SerialUSB.println("Power On!"); if(!wio.waitForNetworkRegister()) SerialUSB.println("Network error!"); return; else SerialUSB.println("Network ready!"); // Change xxxxxxxxxxx to your test phone number if(wio.sendSMS("185XXX26402", message)) SerialUSB.println("Send OK!"); else SerialUSB.println("Send Error!"); void loop() AT_bypass();- Step 10.Use COM monitor tools to print the serial message. Please do not use Arduino IDE COM monitor! That may cause the next time downloading fail, but reopen Arduino IDE can recover that issue.- Step 11. The phone number owner will receive the message.
#include "gnss.h"char nmea_sentence[192];char nmea_GSV_sentence[512];GNSS gnss = GNSS();void setup() gnss.Power_On(); while(false == gnss.Check_If_Power_On()) SerialUSB.println("Waitting for module to alvie..."); delay(1000); SerialUSB.println("\n\rPower On!"); if(!(gnss.open_GNSS())) SerialUSB.println("\n\rGNSS init failed!"); return; SerialUSB.println("Open GNSS OK."); gnss.enable_NMEA_mode(); // Set output sentence in NMEA modevoid loop() clean_buffer(nmea_sentence, 192); gnss.read_NMEA(GGA, nmea_sentence); SerialUSB.print(nmea_sentence); clean_buffer(nmea_sentence, 192); gnss.read_NMEA(RMC, nmea_sentence); SerialUSB.print(nmea_sentence); clean_buffer(nmea_sentence, 192); gnss.read_NMEA(GSA, nmea_sentence); SerialUSB.print(nmea_sentence); clean_buffer(nmea_sentence, 192); gnss.read_NMEA(VTG, nmea_sentence); SerialUSB.print(nmea_sentence); clean_buffer(nmea_GSV_sentence, 512); gnss.read_NMEA_GSV(nmea_sentence); SerialUSB.print(nmea_sentence); SerialUSB.println("\r\n"); delay(1000);- Step 9.Use COM monitor tools to print the serial message. Please do not use Arduino IDE COM monitor! That may cause the next time downloading fail, but reopen Arduino IDE can recover that issue.- Step 10. We will see below logs.
#include "ethernet.h"Ethernet eth = Ethernet();// const char apn[10] = "CMNET";const char apn[10] = "UNINET";const char URL[100] = "mbed.org";char http_cmd[100] = "GET /media/uploads/mbed_official/hello.txt HTTP/1.0\n\r\n\r";int port = 80;int ret = 0;void setup() SerialUSB.println("Begin..."); eth.Power_On(); while(false == eth.Check_If_Power_On()) SerialUSB.println("Waitting for module to alvie..."); delay(1000); while(!eth.init()) delay(1000); SerialUSB.println("Accessing network..."); SerialUSB.println("Initialize done..."); eth.join(apn); SerialUSB.print("\n\rIP: "); SerialUSB.print(eth.ip_string); if(eth.connect(URL, port, TCP)) eth.write(http_cmd); while(MODULE_PORT.available()) serialDebug.write(MODULE_PORT.read()); eth.close(1); else SerialUSB.println("Connect Error!"); void loop() /* Debug */ AT_bypass();- Step 9. Press RST button to enable the COM port.- Step 10.Use COM monitor tools to print the serial message. Please do not use Arduino IDE COM monitor! That may cause the next time downloading fail, but reopen Arduino IDE can recover that issue. 2ff7e9595c
Comments